Quiz Summary
0 of 25 Questions completed
Questions:
Information
You have already completed the quiz before. Hence you can not start it again.
Quiz is loading…
You must sign in or sign up to start the quiz.
You must first complete the following:
Results
Results
0 of 25 Questions answered correctly
Your time:
Time has elapsed
You have reached 0 of 0 point(s), (0)
Earned Point(s): 0 of 0, (0)
0 Essay(s) Pending (Possible Point(s): 0)
Categories
- Not categorized 0%
- 1
- 2
- 3
- 4
- 5
- 6
- 7
- 8
- 9
- 10
- 11
- 12
- 13
- 14
- 15
- 16
- 17
- 18
- 19
- 20
- 21
- 22
- 23
- 24
- 25
- Current
- Review
- Answered
- Correct
- Incorrect
-
Question 1 of 25
1. Question
The range of surface profile depth is established by:
CorrectIncorrect -
Question 2 of 25
2. Question
There are a variety of surface cleanliness standards: several of them have been published by the joint efforts of:
CorrectIncorrect -
Question 3 of 25
3. Question
Regarding pre-surface preparation issues such as verifying that fabrication defects are corrected, the contractor should not be required or expected to perform corrective action unless the governing specification requires it.
CorrectIncorrect -
Question 4 of 25
4. Question
Weld spatter on the surface of the substrate can cause:
CorrectIncorrect -
Question 5 of 25
5. Question
Sharp edges present special challenges to the coating applicator, because the:
CorrectIncorrect -
Question 6 of 25
6. Question
Stripe coating is:
CorrectIncorrect -
Question 7 of 25
7. Question
Grease and oil left on the surface of a substrate can:
CorrectIncorrect -
Question 8 of 25
8. Question
If salts are trapped under an applied coating, they can:
CorrectIncorrect -
Question 9 of 25
9. Question
When the service environment is “immersion,” the specifier should allow:
CorrectIncorrect -
Question 10 of 25
10. Question
The most common and most productive method used to clean steel substrates is:
CorrectIncorrect -
Question 11 of 25
11. Question
The depth of an anchor pattern or surface profile is primarily dictated by the:
CorrectIncorrect -
Question 12 of 25
12. Question
In general, which type of coatings is easier to remove by abrasive blast cleaning?
CorrectIncorrect -
Question 13 of 25
13. Question
Clemco, Inc. claims that a 10 psi reduction in blast nozzle pressure equates to a:
CorrectIncorrect -
Question 14 of 25
14. Question
Chemical strippers:
CorrectIncorrect -
Question 15 of 25
15. Question
If a specification requires a “Brush-off Blast” or a “Commercial Blast” or a “Near White Blast” it is automatically implied that the following standard is invoked:
CorrectIncorrect -
Question 16 of 25
16. Question
SSPC-SP11, “Power Tool Cleaning to Bare Metal”:
CorrectIncorrect -
Question 17 of 25
17. Question
A “White Metal Blast” or SSPC-SP5, allows ______ to remain on the surface.
CorrectIncorrect -
Question 18 of 25
18. Question
Prior to final surface preparation, the most important relationship to assess while recording ambient conditions is:
CorrectIncorrect -
Question 19 of 25
19. Question
If the compressed air used during abrasive blast cleaning contains oil or water, it can:
CorrectIncorrect -
Question 20 of 25
20. Question
The photographic guides developed by SSPC to aid in the visual assessment of surface cleanliness were designed to be used:
CorrectIncorrect -
Question 21 of 25
21. Question
Surface profile or the anchor pattern:
CorrectIncorrect -
Question 22 of 25
22. Question
An excessive profile depth may:
CorrectIncorrect -
Question 23 of 25
23. Question
If Testex X-Coarse replica tape is used to measure the surface profile and the measurement is between 1.5 and 2.5 mils, what must be done?
CorrectIncorrect -
Question 24 of 25
24. Question
According to SSPC-PA 17, how many locations (minimum) are assessed for surface profile?
CorrectIncorrect -
Question 25 of 25
25. Question
Which of the following surface profile measurement frequencies is false?
CorrectIncorrect